Vandersteen VCC1 Center Channel Speaker
Vandersteen VCC1 Center Channel Speaker (Trade)
The VCC-1 is the only center speaker that incorporates integral design solutions to the specific center channel requirements. It is immune to lobing response variations and performs consistently at any height or positioning. It is magnetically shielded and can be compensated for any environment. It maintains the critical phase integrity of the original sound and fully complements the main speakers. As an important part of a high-fidelity home theater system, the VCC-1 folds seamlessly into the multi-channel soundfield. Whether reproducing a whisper or a shout; a breeze or a blizzard, it creates a realistic and totally involving experience.
The VCC-1’s coaxial driver is a combination of a 6½ inch woofer and a 1 inch dome tweeter that share the same acoustical center and radiate as a single point source. The aligned driver is immune from multi-driver interference and the resulting response variations and phase irregularities that plague conventional center speakers. The VCC-1 maintains consistent sonic performance over an expansive listening area without hot spots, drop outs or timbre aberrations.
The VCC-1’s phase integrity complements Vandersteenand other phase-correct front speakers. The VCC-1’s aligned woofer and tweeter are both connected in positive polarity through a first-order, transient-perfect crossover to maintain the original phase and time characteristics of voices, music, special effects and other film sounds.
When the VCC-1 is used with phase-correct main and surround speakers, it will contribute to the significant sonic and spatial benefits of a phase coherent home theater system. But regardless of the phase characteristics of the other speakers, the VCC-1’s many advanced design features will yield superior consistency and enhanced system performance.
Two levels of response compensation are incorporated into the VCC-1 to improve its integration with the main speakers and help counter the sonic effects of nearby walls or other surfaces. The primary compensation attenuates the bass response to enhance blending with the main speakers through the range where their response fully overlaps with the center channel. The secondary compensation, which is activated by a switch on the VCC-1’s rear panel, provides additional compensation for situations where the center speaker is mounted in a wall unit or situated near a wall or other broad surface.
The VCC-1’s aligned, coaxial driver uses a rigid, acoustically inert cast-metal basket to improve cone movement accuracy and resist sympathetic resonances. The 6 1/2 inch woofer’s filled polycone insures high internal stiffness while the 1 inch alloy dome tweeter is ferrofluid cooled to increase power handling and critically damped for smooth response. The driver is magnetically shielded so that it will not affect the picture on your television set. The transient-perfect, first-order crossover’s computer-grade components, including high-quality film capacitors in the signal path, are hand soldered on a double-sided, plated-through PC board for superior consistency and reliability.
The input block is directly soldered onto the circuit board and the driver elements are connected with custom high-purity wire for maximum signal transfer. The enclosure is constructed of 1 to 1 1/2 inch thick constrained-layer-dampened MDF, an advanced multiple-layer material that effecttively damps vibration and controls cabinet resonances. The veneered top and bottom and the acoustically transparent grille cloth allow the VCC-1 to complement any decor. Information on the availability of custom finishes is available from your authorized Vandersteen dealer.
|Coaxial Woofer/Tweeter||6.5” Mineral-Filled Polycone with Die-Cast Basket with 1” Critically-Damped Alloy-Dome Tweeter|
|Recommended Amplification||30-200 Watts Into 8 Ohms|
|Frequency Response||80Hz – 21kHz +/- 3dB|
|Sensitivity||86 dB, 1 meter with 2.83 volt input|
|Impedance||8 ohms nominal 5 ohms|
|Crossovers||First order/6dB per octave, 3.5kHz|
|Input Terminals||Barrier strips, 7/16″ max width|
|Dimensions (WHD)||12 1/8” x 9 1/4” x 10 1/8”|
|Weight||23 lbs. Ea. Ne|